- Winchester Model 42 Owners Manual
- Winchester Model 94 Owners Manual
- Model 59 Winchester Owners Manual
- Winchester Owners Manual
- Winchester Model 23 Owners Manual Download
- Winchester Model 21 Owners Manual
- Winchester Model 23 Owners Manual Pdf
A Model 21 Trap grade st. Grip by Wingshooter62 » Tue May 20, 2014 3:02 am Last post Last post by SHOOTER13 Tue May 20, 2014 6:48 pm 2 Replies Replies 2703 Views Views; My Model 21 Trap by winmod21 » Fri Oct 07, 2011 2:56 pm Last post Last post by winmod21 Fri Dec 02, 2011 2:00 am 23 Replies Replies 12250 Views Views. Aug 01, 2020 The Winchester Model 25 hammer-less slide-action solid-frame shotgun was introduced in 1950. It was made in 12-ga. Only, for the 23/4' shell, and was essentially a moderately priced version of the Winchester Model 12 takedown shotgun. The Model 25 was offered in either 26' or 28' barrel lengths with an option of full or modified choke in the 28' length, or improved cylinder boring in the 26.
The Winchester Model 25 hammer-less slide-action solid-frame shotgun was introduced in 1950. It was made in 12-ga. only, for the 23/4' shell, and was essentially a moderately priced version of the Winchester Model 12 takedown shotgun. The Model 25 was offered in either 26' or 28' barrel lengths with an option of full or modified choke in the 28' length, or improved cylinder boring in the 26' length. Magazine capacity is 4 shells and a wood plug was furnished to reduce the capacity to 2 shells. Weight of the gun with 28' barrel is approximately 8 lbs. and overall length is 41 Va'.
The Model 25 shotgun was discontinued in 1957.
- Attention owners of Winchester model 100 rifles and carbines please read this notice. In July of 1990 the following product safety warning was issued by Winchester. It has come to our attention that the firing pin in the Winchester Model 100 Rifle or Carbine may break due to use and metal fatigue and become lodged in the breech bolt face.
- Winchester Model 21 20 gauge 28-inch barrels It seems this fine Winchester Model 21 20 ga, serial # 4956 has spent much of it’s lifetime not far from its place of manufacture. It is in ou.Click for more info.
Winchester Model 42 Owners Manual
By THOMAS E. WESSEL
1. Barrel*
3. Magazine band screw
4. Magazine band
5. Magazine lock screw
6. Magazine lock
7. Receiver
8. Magazine
9. Action slide spring
10. Magazine plug
11. Magazine plug screw (2)
12. Magazine spring
13. Magazine follower
14. Breechbolt
15. Firing pin stop pin
16. Left extractor pin
17. Left extractor
18. Left extractor spring
19. Right extractor spring
20. Right extractor spring plunger
21. Right extractor
22. Firing pin spring
23. Firing pin striker
24. Firing pin
25. Buttplate
26. Buttplate screw (2)
27. Receiver shank *
28. Buttstock bolt
29. Buttstock bolt washer
30. Cartridge cutoff
31. Ejector
32. Ejector spring
33. Action slide
34. Action slide sleeve screw cap
35. Guard
36. Guard screw
37. Action slide lock *
38. Action slide lock screw *
39. Action slide lock pivot *
40. Action slide lock spring *
41. Carrier plunger screw
42. Carrier plunger spring
43. Carrier plunger
44. Carrier Sql prompt 10 key.
45. Cartridge guide
46. Cartridge guide pivot *
47. Carrier spring
48. Carrier pivot
49. Trigger lock
50. Trigger lock plunger spring
51. Trigger lock plunger How to uninstall parallels on a mac.
52. Hammer pin
53. Trigger pin
54. Trigger
55. Trigger spring
56. Hammer spring
Winchester Model 94 Owners Manual
57. Hammer spring guide rod
58. Hammer spring guide pin
59. Hammer
Model 59 Winchester Owners Manual
60. Buttstock
Winchester Owners Manual
61. Action slide handle
* Factory assembly to other major part. Do not disassemble.
ITo properly disassemble Model 25 it is necessary to fabricate 2 special tools. Make Tool A from 6' or 8' bar of Va' x -lío' cold-rolled steel stock. Drill and shape end as shov,n. Holes should be slightly chamfered and all edges deburred.
Make Tool B from an 8' length of tempered steel dimensioned as shown. An old power hacksaw blade is excellent. Grind or file double end to form screwdrivers
4 Remove guard screw (36) and swing guard (35) down out of receiver (inside left wall of receiver shown). Lift out cartridge cutoff (30). With small screwdriver, pry out ejector (31—arrow) at rear of breechbolt (14) in receiver. Slide breechbolt fully rearward and lift out.
Remove buttplate screws (26), butt-plate (25), buttstock bolt (28). and washer (29). Pull off buttstock (60). In reassembly, replace buttstock after replacing guard
2 Remove magazine band screw (3) and slide magazine band (4) forward on barrel (1). Remove magazine lock screw (5) and magazine lock (6) in face of receiver (7). Apply Tool A to lug in front of magazine plug (10) aligning Va' hole in tool with hole in plug. Insert short piece of Va' drill rod (A) and turn out magazine (8) approximately 150°.
Tool is necessary to 'break' tight screw fit of magazine to receiver. Unscrew magazine, with action slide handle (61) attached, from receiver by hand. Pull entire assembly straight forward and free of gun
3 Unscrew magazine plug screws (11), holding magazine plug in place with thumb. Fl studio 12 regkey file. Slowly remove magazine plug and grasp magazine spring (12) to prevent its escape. Remove spring and follower (13).
Apply Tool B to action slide sleeve screw cap (34) as shown and unscrew it. Pull off action slide handle and withdraw magazine from action slide (33). Remove action slide spring (9). When reassembling, be sure this spring is on rear side of stop collar on magazine
5 Push back right extractor plunger (20) with small screwdriver and lift out right extractor (21) together with plunger and spring (19). Drift out left extractor pin (16, arrow) from bottom of breechbolt and lift away left extractor (17) and spring (18). Drift out firing pin stop pin (15) and remove firing pin striker (23). firing pin (24), and firing pin spring (22). Reassemble bolt in reverse
6 Unscrew carrier pivot (48). This has a left thread and unscrews right. Remove carrier (44) and carrier spring (47), with cartridge guide (45) attached. Let hammer (59) down slowly and drift out hammer pin (52) from the left. Remove hammer with hammer spring (56) and hammer spring guide rod (57).
Drift out trigger pin (53) and remove trigger (54) and trigger spring (55). Do not disassemble action slide lock (37) assembly from guard as lock screw (38) is 'staked' to lock pivot (39).
Winchester Model 23 Owners Manual Download
To remove trigger lock (49) insert small pin into hole in lock, turn Va turn and at same time push trigger lock out from left to right. Reassemble in reverse ■
Was this article helpful?
Hunting Mastery Selected Tips
Deer hunting is an interesting thing that reminds you of those golden old ages of 19th centuries, where a handsome hunk well equipped with all hunting material rides on horse searching for his target animal either for the purpose of displaying his masculine powers or for enticing and wooing his lady love.
Winchester Model 21 Owners Manual
![Winchester Winchester](https://www.cornellpubs.com/Images2/Win%2012%20Manual.jpg)